Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
Presented here down the page you might get lots of extremely good news regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the job can relocate speedily; if you need to open up a wall to eliminate the old tub and also position the new bath tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will require an assistant to vacate the old tub as well as set in the brand-new one. Ensure you have certified on your own for the task as well as are comfortable trying it. As opposed to hiring a contractor to take over a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly aid you set up a new bathtub in your washroom if you have actually already gotten a brand-new bathtub and don't require to change the setup of your previous supply of water pipes.
Your tools and material list must consist of the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath needs to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final setting.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the water. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub till the spirit level reviews level.
To set up taps, fit the bottom of the outermost versatile faucet connector to the suitable supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water as well as check all joints and also new pipework for leakages and also tighten them if required. Fill up the tub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub should wait until the bath tub has actually been utilized at least when as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin guaranteeing that the washing machines remain in area between the faucet as well as the sink. Secure the tap in position with the producer provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The previous kind must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, resulting in issues with wetness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and also are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also quickly readily available on the marketplace. It is a good idea to fit the tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our part on How to Install a Bathtub. Thanks a ton for taking time to read through our posting. Enjoyed reading our content? Please share it. Let someone else discover it. We take joy in reading our article about Installing A Bathtub.
Emergency leaks? Professional help here. Report this page